;         IOSMAIL.CFG => IOSMAIL Configuration File!
;
;                             by....
;
; ***  **  Erik Williams
; **  ***  SunFox Productions, Ltd.
; ***  **  University of Central Florida, Orlando
; **  ***  REALITY.SYS corrupted!  Restart universe (Y/N)?
;
;
; Like BINKLEY.CFG in this archive, all you should have to do with
; this file is edit the node numbers and paths.
;
;
; This is the only label I have needed for IOS...it imports and
; exports mail in one pass and keeps the mail packets around in
; case there was any problems.  The three events prepare a "POLL
; FILE" for 51:1/0...a 60-byte file that will cause Bink/ST to
; call out automatically to the Twilight Zone.
;
;
#INANDOUT
Commands -a -i -s -c -x -p -o -t
Event All 00:00 00:05 Prepare-Poll 51:1/0.0
Event All 05:59 06:05 Prepare-Poll 51:1/0.0
Event All 11:59 12:05 Prepare-Poll 51:1/0.0
SendAlwaysPKT
#endlabel
;
#ENDALL
;
;
; "Hello, my name is..."
;
;
SysOp           Erik Williams
;
;
; These address statements are placed in the exact same order as
; used in BINKLEY.CFG.
;
;
Address         51:1/11.0
Address         1:363/169.0
;
;
; ApplZone is roughly equivalent to the Domain statement in
; BINKLEY.CFG.  It takes the zone number, the path to the outbound
; folder associated with that zone (*WITHOUT* the hex representation
; of the zone number...IOS figures that out with the first parameter),
; and the nodelist associated with that zone.
;
;
ApplZone        51 d:\atarinet\ atrinet.ftn
ApplZone        1 d:\fidonet\ fidonet.org
;
;
; The password statements are very important in terms of routing mail.
; Every node you communicate with must have a Password keyword associated
; with it, even if that Password keyword does not have an actual session
; password in the directive!  An example of the latter is the Password for
; 51:3/6...all I am doing is telling IOS that I want all mail to Bryan
; Hall's board to be LZHmail.
;
; Before you send crashmail to a node, make sure your IOSMAIL.CFG has a
; Password and a Route for that node (more on Route in a minute).
;
;
Password  51:1/0.0 # $xxxxx %LZHmail
Password  51:3/6.0 # %LZHmail
Password  1:363/31.0 # $xxxxx %ARCmail
Password  1:363/112.0 # $xxxxx %LZHmail
Password  1:363/32.0 # %ARCmail
;
;
; The following keywords control the logging done by IOS.  LogFile tells
; IOS where to place the log, LogLevel tells IOS how much I want (level
; 1 is pretty darned verbose), and DateFormat allows me to specify the
; time stamping to log entries.
;
; My DateFormat will produce a log-line like this:
;
;    # 06 Oct 00:00:06 IOS  IOSmail 0.89 execute INANDOUT
;
; NiceOutput and MSGreport add some descriptive logging to the logfile.
;
;
Logfile          d:\logs\ios.log
LogLevel         1
DateFormat       %d %b %H:%M:%S
NiceOutput
MSGreport
;
;
; Here are two special message area definitions.  Netmail is just like
; its counterpart in BINKLEY.CFG.  The TrashArea is for messages that
; do not fit with the echoes defined in AREAS.BBS (my AREAS.BBS is
; included in this archive)...so they will be dumped here!
;
; An example would be if A_BBS_ADDS is the definition in AREAS.BBS, but
; the incoming messages are for area A_BBS_ADS, then the incoming messages
; will be tossed into the TrashArea.
;
;
Netmail         d:\netmail\
TrashArea       d:\mess\a_bad
;
;
; Here are the archiver specifications for ARC, LZH, and ZIP...the three
; major compression schemes.  If the inbound packet does not match one of
; these schemes, then the archiver specified with the Archiver keyword
; will try to work with the packet (in this case, I use WhatArc 2.02).
;
;
Archiver        c:\turbo\bink\whatarc\whatarc.ttp x a
ARCarchive      c:\turbo\bink\whatarc\arc602.ttp x m
LZHarchive      c:\turbo\bink\whatarc\lharc.ttp x m -m
ZIParchive      c:\turbo\bink\whatarc\zipjr.ttp -x -a -mt
;
;
; Here are the paths I use for IOS...the Inbound and Outbound are
; exactly the same as the inbound and hold paths in BINKLEY.CFG.  The
; MailTemp keyword specifies a temporary directory for uncompressing and
; working with the mail packet.
;
;
Inbound         d:\netfile\
Outbound        d:\atarinet.033\
MailTemp        d:\temp\
;
;
; The Route statements are used to tell IOS where mail should go out
; there in net.land.  The Routes work in conjunction with the Password
; directives earlier in this configuration file.  Note that you can use
; wildcards to replace specific node numbers...in fact, you will more
; than likely use this for all of your host-routed mail!
;
; You must have a route to a node for crashmail (hence the reason for
; the routes without wildcards.  When you write crashmail, make sure
; that you have the Route and the corresponding Password entries in
; this file.
;
;
Route    51:1/0   51:*
Route    51:3/6   51:3/6
Route    1:363/31 1:*
Route    1:363/32 1:363/32
Route    1:363/42 1:363/42
;
;
; Miscellaneous mail traffic control directives and other stuff.
;
;
File-To         *
Arc-For         51:* 1:*
NewBinkley
;
;
; Other miscellaneous directives.
;
;
AddDomain 51 1
AreaConsultant -R -L -Q
PKTtemp d:\temp\
SendAlwaysPKT
MinMessages 10000